MIMAKI JV5-130S Specifikace Strana 230
- Strana / 292
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
6 Operation for Functions
6-18
Functions of [INFORMATION] key
This section describes briefly the [INFORMATION] functions and their setting values.
Setting a MACHINE SETUP
The operation described below on the operation panel is required to execute machine setup functions.
STEPS:
1 Make sure that the printer is in LOCAL mode, and then select [MACHINE SETUP]
using the [FUNCTION] key and press the [ENTER] key.
If it is in REMOTE mode, press the [REMOTE] key once.
2 Select a machine setting function and make setting.
Name Function Refer to
ERROR HISTORY Displays the history of errors. p. 6-24
MAINTE. HISTORY
Displays the records of the date and time when maintenance functions were
used.
p. 6-24
PRT.modeHISTORY
Displays the history of information (printing conditions) of the online print-
ing that has been performed up to now.
p. 6-24
LIST Prints the data for the operator to check the settings of the printer. p. 6-25
Ink REPL. Report Draws ink cartridge replacement information. p. 6-25
VERSION Displays various version information of the equipment. p. 6-25
Serial&DealerNo Displays serial No. and dealer No. of the printer. p. 6-25
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
FUNCTION
MACHINE SETUP <ENT>
- OPERATION MANUAL 1
- Foreword 2
- DISCLAIMER OF WARRANTY 3
- Requests 3
- About media 4
- FCC Statement (USA) 4
- TABLE OF CONTENTS 7
- CHAPTER 3 Printing 8
- CHAPTER 4 Daily Care 9
- CHAPTER 5 In Case of Trouble 10
- CHAPTER 1 13
- Safety Precautions 13
- Checking the accessories 14
- Dry fan unit Box 15
- Features 16
- (See 1-8) 19
- Notes on Installation 20
- Notes on Location 21
- Moving the printer 22
- Connecting Power Supply 23
- WARNING 24
- Precautions in Use 25
- CAUTION 25
- CAUTIONS and NOTES 26
- Warning for Use 27
- CAUTIONS and NOTES 27
- Recommended types of media 28
- Warning labels 29
- Basic specifications 30
- Specifications for ink 32
- Notes on USB 2.0 Interface 34
- 1 Safety Precautions 36
- CHAPTER 2 37
- Before Use 37
- Configurations and Functions 38
- 2 Before Use 40
- 2 Press the [ENTER] key once 41
- L Cyan or Blue 43
- BL Light Cyan or Light Blue 43
- Cartridge control 44
- Carriage 46
- Capping station 46
- Cutter blade and cutting line 47
- Media sensor 47
- Pinch roller 48
- Feed roller 48
- Clamp lever 48
- Post-heater 49
- Print heater 49
- Pre-heater 49
- Operation Panel 50
- How to read the display 51
- Job processing status 52
- Message indicating status 52
- How to use the keys 54
- Functions of the JOG keys 55
- Modes and Menu Screens 56
- About Function Menus 57
- 2 Press the [FUNCTION] key 58
- Outline of menu hierarchy 60
- Direct keys 62
- SET UP functions 63
- MAINTENANCE functions 65
- MACHINE SET functions 68
- NCU functions 70
- CHAPTER 3 71
- Printing 71
- Operation flow 72
- Turning the power on 73
- Power Switches 74
- Adjusting the head gap 75
- 3 Press the [END] key 76
- 2 Select a angle as setting 78
- 3 Retighten the knobs 78
- Roll holder securing screw 79
- Media support bar 80
- Rightmost pinch roller 83
- Suction hole 83
- Media press 83
- Media end 83
- Input of MediaLength 86
- MEDIA LENGTH = 50 m 86
- Setting the torque limiter 87
- 4 Push down the clamp lever 89
- How to select a user type 90
- How to check the user type 90
- Operating the heaters 91
- 2 Press the [HEATER] key 92
- Example of beading 93
- In case of heater trouble 95
- [PG DROP ADJUST.] 96
- Abnormal pattern 98
- Normal pattern 98
- 2 Press the [CLEANING] key 99
- 5 Press the [ENTER] key 100
- 4 Press the [ENTER] key 102
- CORRECTION PATTERN 103
- Correction value is too small 104
- Correction value: 104
- -255 ~ 255 104
- Correction value is too large 104
- OverlapClearance 104
- 6 Press the [ENTER] key 106
- Effective Plotting Area 107
- Establishing the Origin 108
- Printing an image 109
- 3 Press the [ENTER] key 111
- 2 Press the [] key 112
- Automatic cleaning 113
- 4 Press the [FUNCTION] key 114
- When setting to CLEANING 115
- When setting to WIPING 117
- [INK NEAR END] 118
- [INK END] 118
- [INK END][INK NEAR END] 119
- 2 Press the [ENTER] key 120
- 3 Printing 122
- EXPIRED INK IN USE 124
- NOT RECOMMENDED !! 124
- PRESS [ENT] 124
- 8 to 10 125
- 2 Press the [REMOTE] key 126
- Turning the power off 127
- CHAPTER 4 129
- Daily Care 129
- Routine Maintenance 130
- Notes on cleaning solution 131
- Cleaning exterior surfaces 131
- Cleaning the platen 131
- Cleaning the media sensor 132
- Cleaning the media press 132
- Opening the maintenance cover 133
- L. ∗ > [JV5-01] 135
- ST.MAINTENANCE 135
- CARRIAGE OUT <ent> 135
- COMPLETED :end 137
- ∗Being Initialized∗ 137
- PLEASE WAIT 137
- 7 Press the [ENTER] key 140
- 12Press the [ENTER] key 141
- 11Press the [ENTER] key 147
- To step 5 To step 11 148
- PUMP tube cleaning 151
- 4 Daily Maintenance 152
- Wiper cleaning 153
- [CR.MAINTENANCE] 156
- Clean the head media sensor 157
- 9 Press the [ENTER] key 158
- Input range: OFF, 1 to 168 160
- [ROUTINE SETUP] 162
- Other maintenance functions 169
- [BOX EXCHANGE LV] 171
- L .1 > [ JV5-01 ] 172
- ! WasteTANK FULL/NONE 172
- ! NearFULL WASTE TANK 172
- Cleaning of Flushing Box 174
- 3 Open the pump cover T 175
- When this figure reaches 176
- 100%, the warning or error 176
- Replacing F-Box filters 177
- F-BOX filter 178
- F-BOX filter base 178
- 1 Press [] key 179
- [FILTER EXC. LV.] 181
- 3 Open the front cover 187
- Install the new cutter unit 188
- CHAPTER 5 189
- In Case of Trouble 189
- Power does not turn on 190
- Check the basic operation 191
- If image quality is poor 192
- (jet deviation) 193
- [DISCHARGE&WASH] 194
- 4 Remove the ink cartridges 195
- 5 In Case of Trouble 198
- Ink cartridge trouble 200
- Warning messages 203
- Error messages 206
- CHAPTER 6 213
- Operation for Functions 213
- Invoking SET UP functions 214
- (See 6-31) 216
- (See 3-33) 216
- PRINT MODE 217
- INK LAYERS 219
- DRYING TIME 219
- AUTO CUT 220
- PRE-FEED 220
- COLOR PATTERN 220
- PRIORITY 221
- (See 3-43) 222
- (See 3-45) 222
- (See 3-5) 222
- MEDIA DETECT 223
- SETUP RESET 223
- List of functions 224
- 2 Press the [ST.MAINT] key 225
- [MEDIA RESIDUAL] 226
- 6 Operation for Functions 228
- Setting a MACHINE SETUP 230
- DRY & EXHAUST FAN 231
- DRYNESS FEED 232
- CONFIRM. FEED 232
- PRE-FEED METHOD 233
- HEATER SETUP 233
- MEDIA CUT 233
- TIME SET 233
- UNIT SETUP 234
- STAMP SETUP 234
- Test Draw Arrange 235
- Detection of media 235
- MACHINE NAME 235
- INFORMATION 236
- ERROR HISTORY 236
- MAINTE. HISTORY 236
- PRT.modeHISTORY 236
- Ink replacement report 237
- Serial&DealerNo 237
- Invoking NCU functions 238
- Outline of the NCU functions 239
- NG JUDGEMENT (*1) 240
- COND.INDICATION 240
- DISPLAY setting 241
- Applied settings of functions 242
- Detailed settings of heaters 243
- Input range: 244
- PRE [OFF, 20 - 60] ° C 244
- PRT [OFF, 20 - 60] ° C 244
- POST [OFF, 20 - 70] ° C 244
- How to operate function menus 245
- Change is 247
- Functions related to ink 248
- Function Flowchart [BOOT] 250
- DECIDE = [ENTER] 262
- TIMER SET = [FUNC.] 262
- CLtypeSetWithFUNCkey 267
- :FORE&BACK 280
- 10 to 1000 280
- D201515-21-31102014 290
- Printed in Japan 292
Související produkty a manuály pro Tisk a skenování MIMAKI JV5-130S
Tisk a skenování MIMAKI JV5-320S Specifikace
(130 stránky)
(130 stránky)
Tisk a skenování MIMAKI Tx2-1600 Manuál s instrukcemi
(166 stránky)
(166 stránky)
Tisk a skenování MIMAKI JV33-160 Specifikace
(202 stránky)
(202 stránky)
Tisk a skenování MIMAKI JV3-75SPII Specifikace
(150 stránky)
(150 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce