MIMAKI JV3-160S Průvodce nastavením Strana 51
- Strana / 170
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
– 3.13 –
3-3-5. Fan motor
Problems The fan motor fails to turn.
The fan motor cannot be stopped running.
Causes 1) A part of motor cable has disconnected.
2) Clip the fan motor assy cable in the platen cover to short-circuit the fan
motor.
Checking procedures 1-2) Visually confirm the fun motor status.
([ACTION TEST - FAN MOTOR])
Remedies 1) Replace the fan motor assy. with a new one.
3-3-6. Abnormal nozzle discharge
Problems When checking the nozzle, the nozzle at the enter of the head does not print.
The edge of the nozzle does not print.
Causes 1) The amount of wiper contact is larger or smaller.
2) The capping position with respect to the head is not normal.
Checking procedure 1) Make visual check of the amount of wiper contact.
2) Perform the check test / the capping position.
(Refer to [6-6-2. Adjustment of the station position.])
Remedies 1) Adjust the amount of wiper contact.
2) Perform the adjustment of the station position.
- JV3 Series 1
- FOREWORD 3
- TABLE OF CONTENTS 4
- CHAPTER 3 TROUBLESHOOTING 4
- CHAPTER 4 ADJUSTMENT 5
- CHAPTER 1 9
- OVERVIEW OF MAINTENANCE 9
- 1-1. Cautions in maintenance 10
- 1-4. Names of parts 12
- 1-4-2. Rear face 13
- Name Function 13
- 1-5. Specifications 14
- Item JV3-130S JV3-160S 15
- JV3 series specified ink 16
- 1Solvent ink (SPC-0334∗) 8 16
- – 1.10 – 18
- CHAPTER 2 19
- EXPLANATION OF OPERATION 19
- 2-1-1. Operations 20
- Heater block diagram (2/2) 22
- 2-1-2. Power supply 23
- 2-1-3. Main PCB 23
- Main PCB block diagram 24
- Main PCB Connector signals 25
- 2-1-4. 1394 PCB 27
- 2-1-5. I/F Connection PCB 27
- 2-1-6. IO PCB 28
- IO PCB Connector signals 28
- 2-1-7. IO2 PCB 29
- IO2 PCB Connector signals 29
- 2-1-8. Slider PCB 30
- Slider PCB Connector signals 30
- 2-1-9. Linear encoder PCB 31
- 2-1-10. The KeyBoard PCB 31
- 2-1-11. Take-up motor PCB 31
- 2-1-12. ID contact board 31
- 2-2. Ink system 32
- Refreshing operation 34
- Standby state 34
- Ink end monitoring 34
- Head cleaning operation 35
- Ink cartridge replacement 35
- Miscellaneous 35
- Ink parameters 1 36
- 2-2-4. IC Chip Function 37
- IC chip detecting timing 37
- CHAPTER 3 39
- TROUBLESHOOTING 39
- – 3.10 – 48
- 3-3-3. Cutting failure 49
- 3-3-4. Faulty cutter 50
- 3-3-5. Fan motor 51
- 3-3-7. Abnormal ink shot 52
- – 3.15 – 53
- 3-3-11. Cannot read the IC 54
- Main PCB 54
- 3-4. Plotting failure 55
- 3-4-2. Abnormal print 56
- – 3.19 – 57
- – 3.20 – 58
- – 3.21 – 59
- – 3.22 – 60
- – 3.23 – 61
- – 3.24 – 62
- 3-4-10. Banding occur 63
- 3-4-11. Vertical stripes 63
- 3-4-13. Ink drop or mist 64
- CHAPTER 4 65
- ADJUSTMENT 65
- 4-2. Maintenance item 68
- Pertinent Wiper height 75
- Pertinent Cap height 75
- (Insert from front side) 76
- Screw (M3) 76
- Wiper adjusting plate 0.5 76
- Cap adjusting plate 0.5 76
- Suction side connection joint 78
- Mounting screw 80
- Linear sensor PCB assy 80
- Optical axis 80
- – 4.17 – 81
- 4-2-12. Heater Replacement 83
- • Do not remove the cap bolt 84
- Write a number 85
- 4-2-13. Replacement Fuse 89
- – 4.26 – 90
- CHAPTER 5 91
- MAINTENANCE MODE 91
- 5-1. Maintenance items 92
- #PARAMETER 93
- key and 94
- Head2 Head1 99
- #PRN. adjust2 V2 101
- Y Bi. 1-1 : 0.0 101
- FINAL. 1-2 : 0.0 101
- FUNCTION 102
- Replace count 106
- 5-3-6. CAPPING 108
- 5-3-7. HEAD ID 109
- 5-3-8. SERIAL NO 110
- 5-3-9. DEALER NO 111
- 5-3-10. WORM WHEEL 112
- 5-3-13. SET QUALITY 117
- 5-3-14. MEDIA COMP2 118
- REMOTE/LOCAL 122
- 5-4-4. X SERVO 129
- 5-4-5. Y SERVO 130
- 5-4-6. XY SERVO 131
- 5-4-13. PUMP MOTOR 142
- 5-5. #PARAMATER items 153
- – 5.64 – 154
- – 5.69 – 159
- Error messages 159
- 5-7. Updating the firmware 160
- – 5.73 – 163
- – 5.74 – 164
- CHAPTER 6 165
- MAINTENANCE MENU TREE 165
- 6-1. Maintenance menu tree 166
- D500200-1.00-13122002 170
Související produkty a manuály pro Tisk a skenování MIMAKI JV3-160S
Tisk a skenování MIMAKI UJF-706 Specifikace
(184 stránky)
(184 stránky)
Tisk a skenování MIMAKI JV3-130SPII Specifikace
(142 stránky)
(142 stránky)
Tisk a skenování MIMAKI JV5-130S Specifikace
(292 stránky)
(292 stránky)
Tisk a skenování MIMAKI JV5-320S Specifikace
(130 stránky)
(130 stránky)
Tisk a skenování MIMAKI Tx2-1600 Manuál s instrukcemi
(166 stránky)
(166 stránky)
Tisk a skenování MIMAKI JV33-160 Specifikace
(202 stránky)
(202 stránky)
Tisk a skenování MIMAKI JV3-75SPII Specifikace
(150 stránky)
(150 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.113 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce